Two-Tier Antique Mahogany Table

Table Before Repair

Table After Repair & Refinishing

This table came to me as you see in the photo on the right, with three legs that were broken, the center piece which held them together was missing on two out of the three legs.

These missing sections had to be reconstructed using a template, traced from the legs themselves. This was an lovely antique two-tier table commonly seen during the 1920's and 1930s. Many people remember these tables in their grandparents homes, so they now hold a special place in our hearts along with all those memories. Commonly used for knick-knacks, plants, collectibles and many other

Dining Table Top Refinished

Table Top Before

Table Top After

We all know how much we use our tables, therefore the top of them tends to get plenty of use, which is okay, because that's what they're for. This solid oak table was purchased twenty-five years ago and got plenty of use, so the top had some wear on it. Nothing too bad, but enough to justify a refinish, top only. It also had two leaves, so the owner wanted those refinished as well.

This great table was made by the Amish and the quality of the workmanship showed. Amish are known for their precision and attention to details as well as simplicity in structure so their furniture is easy to use and guaranteed to last a long time. The woodgrain of this table was beautiful, which became apparent after I totally stripped the top.

I kept the leaves on the table and stripped them in place (much easier) and made sure the sides of the

Artistic End Table

End Table Before

Leather on an end table such as this was commonly used for furniture as a decorative effect for the top. It worked nicely when new, but over the years these tables' leather got pretty beat up. Scratches, gouges, tears and discoloration became more common than shiny new leather and it no longer looked pretty, just old and worn out.

End Table After

While I wasn't quite sure what I would do to replace the leather which was peeling up on one side, it needed to be completely removed, which had proven to be quite a task, as the non-lifted portion adhered quite well. I had to use a small heat gun to soften the adhesive enough to carefully slip my putty knife under the leather and slowly peel it off the wood. It took about 30 minutes, but I was successfully able to lift the last corner of the leather and tear it off. Goodbye old leather, hello new design.

I used a chisel to scrape remaining paper left by the leather section, then sanded the surface smooth. While I was unsure exactly what I would do to replace the leather, I knew that when the time came, I'd have exactly the right treatment, so I got to work on the rest of it. I stripped, sanded and stained the end table using cherry stain, which brought out the gorgeous tones in the cherry wood the table was made from. Making a decision on stain can be tricky, since you don't really know how it will look until you apply it. A darker stain would have hidden much of the wood grain, so cherry was the perfect choice for this end table.


Once stained, I put this table aside while working on other furniture items for this project, (while my I left my subconscious work on the creative side of how to make the top stand out). Eventually I had formulated an idea which involved my trusty carpenter, my husband Jim. I had asked him to make custom veneer sections out of oak and mahogany, so he sliced up sixteen 1-1/2" sections of veneer, more than enough to experiment with a workable design for the tabletop.

End Table After

Using the freshly cut veneer sections, I laid out the pieces and worked up a design, much like one would put together a puzzle, only you create the design as you go. It took a while as I played around with the length of each piece, layout and design, but eventually I had created a random pattern I was satisfied with, then applied adhesive to the table and each veneer section, then let everything dry for fifteen minutes before I carefully positioned each section into place. There's no forgiveness when you work with adhesive cement on both sides of the wood. Once they're down, they're down, so it's a good idea to "dry fit" them before you apply the adhesive.

After sanding the tabletop to get all the veneer sections level, I applied golden pecan stain. Because of the two distinct woods, each wood had taken on a different tone, which created an interesting, artistic and contemporary tabletop. Once the stain was dry, I applied two coats of polyurethane to the lower areas and legs of the table and three coats to the top for added protection. It looked fabulous! This was definitely one of my favorite projects as I was able to blend the craft of refinishing, with the art of creating a custom made veneer design that gave this old beauty a modern, updated look.

This table was one of four pieces of furniture we did at the same time. Click on the links below to see the others:

http://finalefurniture.blogspot.com/2017/04/antique-secretary.html
http://finalefurniture.blogspot.com/2017/04/antique-writing-desk.html
http://finalefurniture.blogspot.com/2017/04/antique-piano-bench.html

Edwardian Console

Console Before Refinishing

Console After

This console was an extraordinarily large piece of furniture. It's hard to judge the scale of this piece standing alone, but it comes up to the center of my five foot frame and is approximately six feet wide and twenty-one inches deep in the middle.

It had many surface scratches and had seen some wear, mostly on the top where the veneer had worn off and on the sides where the veneer had peeled off on one side and was half gone on the other. Before anything else could be done, I needed to repair that veneer on the one side and add a section to the missing left side. Luckily I was able to match the existing veneer pretty close. With veneer it's a gamble, because most of these pieces were done many years ago and the veneer they used was quite different from today's selection, but I was satisfied the veneer was appropriate for this piece and blended quite nicely.

Cheap TV Stand Makeover

TV Stand Before

TV Stand After Paint

This corner tv stand was a very lucky find for me! I had been looking for something to replace the "too tall" temporary tv stand with something lower, since the antique cherry cabinet I had used was too high and blocked a significant amount of light from the window, making it hard to open and close the curtains.

We simply don't have the time to build an adequate tv stand right now with everything else we're trying to accomplish outside before the weather turns cold, so finding this little gem was an unexpected surprise, especially since it cost me only $5.00!

Beautiful Oak Table Refinish

Oak Table Before

This great oak table had strong "bones," but the surface had minor surface scratches and required gentle sanding and a new finish of golden oak stain to create a better than new look. Oak is one of my favorite woods to work with because it handles sanding well, allowing the grain, commonly hidden by layers of grime and

Oak Table After

wear, to come to light. 

Decent sized, this table was the couples' primary dining table, so I made sure I put a "rush" on it and got it done quickly. Lots and lots of sanding and three coats of polyurethane, this little gem was once again a great piece of furniture that can be used for years to come.

Tea Cart Repair

Tea Cart Before

Tea Cart After

This lovely antique tea cart was in need of a broken wheel repair along with refinishing the lower shelf which had seen its share of scratches and wear. Evidently a caretaker who takes care of the owner's ninety-one year old mother had somehow tipped over the cart, breaking the wheel into several pieces.

Made of maple, this tea cart had a gorgeous finish, which I strived hard to maintain while refinishing it. The wheel, however, was a bit of a challenge as it needed to be completely rebuilt.

Using a section of wood that looked close to the original wheel, we were able to make a template of the unbroken wheel, then cut out a brand new one with a scroll saw. The outside of the wheel had to be carved out with a lathe, so that the rubber gasket could be wrapped around it as it had been originally. The finished, repaired tea cart was as good as new and ready to be used for another one hundred plus years.

Antique Desk Cabinet

Cabinet Before

This lovely old cabinet came to us in less than perfect condition. It had seen a lot of use over the years, judging by the scratches and wear, however, we were able to detect the high quality of the wood (tiger oak) and the overall structure of the piece and knew we would be able to breathe new life

into it making it shine again. 

Cabinet After

We determined that this cabinet once had a large door, likely glass, which had opened on left side where the shelves were located, but the owner no longer had the door and didn't mind not having one. The cabinet had only three of the four original wheels. Luckily we had the same style of wheels leftover from a previous job, so we were able to add the fourth wheel, making this piece much easier to move around. (It's a good idea to save hardware!)

Dressers Painted Black

Dresser Before

Dresser After

I found this little treasure at an estate sale along with another dresser (at bottom, which also had a special design detail at the lower edge). I especially loved the top drawer, which was slightly longer than the other three and had a great curvy top, reminding me of an Art Deco style. The dresser was pine, and while the wood was in great shape and would have look good stained, I chose black paint instead.

I knew the two dressers would look great painted black, as long as I could find matching knobs. As always, a full stripping was necessary before priming and painting. I was fortunate to find online sixteen knobs that were light gray porcelain with a "crackled" look. This was the detail needed to link the two different style dressers together so that they made a matched set. It never ceases to amaze me how much paint changes the look and feel of a piece of furniture. In this case, choosing the right paint linked two totally separate pieces together as a matched set.

Dresser Before

Dresser After