Dainty Fluted Chair Reupholstered and Refinished

Armchair Before

This dainty fluted chair, a ladie's chair, was in desperate need of updating and 
love. The fabric was stained and worn, with evidence of a cat who likely used the back to sharpen her nails. Needless to say this chair had seen better days. 

Armchair After

At a glance, the structure looked okay, but after I picked up the chair, the right side collapsed and was wobbly. Clearly there was internal damage to the frame. Once I began removing the fabric, I located the source of the damage. 

The far right support board was cracked and had come apart from the arm. This board needed to be reattached with glue and a single screw. The top curved board was cracked in the center; the inner right board had broken off at the top. Repairs included making a new dowel and reattaching the inner support board and gluing, then screwing the outer side board back in place to make it structurally sound. *(See photo below to see where the chair was broken and repaired).

Once the repairs were made and the structure strong again, the legs were stripped, sanded and restrained then protected with polyurethane. After Jim had worked his magic, it was my turn to tackle the exterior upholstery. 

This chair had zig-zag springs which were in great condition, so they didn’t need to be tightened or replaced. The first step was to cover the springs with burlap, which was stapled to the top edge of the seat. Burlap keeps the springs secure, while providing a good foundation for the layers that follow. After the burlap was secure, I added a 1” thick section of high density foam which covered the entirespring/burlap seating area. A few staples held the foam in place. 

Next, raw cotton was liberally layered on top of the foam, creating a nice “crown” for the chair’s seat. The raw cotton can be purchased per yard, or per a 10 yard bulk, which is the preferred method as it is less costly per yard. The final layer was a 1/4” foam, which was also stapled to keep it secure. I always give it the “sit” test, which is when I sit on the chair and test its softness and support. You shouldn’t feel the springs when sitting on a chair. If you feel springs, there’s not enough padding. I was satisfied with the thickness of the padding, so I cut the fabric for the seat and made the “V” cuts carefully around the arms and legs for a perfect fit. 

This was my first fluted back chair, so I researched how to create the “flutes,” or “channels.” However, before I could get to the fluted portion of the chair, I had to pad the arms and create new fabric panels for the sides. Using raw cotton and foam, I made sure both arms would be soft as well as supportive enough for the new fabric. I chose not to use the old fabric as templates. Instead, I made my own templates from muslin. This allowed me to customize the arms and create a “partial sewn” arm instead of just folding fabric and stapling in place. The fit was perfect. 

I can’t say enough about making an accurate template for upholstery work! It is an essential part of getting that perfect fit. And with plenty of muslin at my disposal, I was able to create accurately measured templates for each arm, then sew them together to test them before I cut the fabric. Templates can save a lot of time and fabric and ensure accuracy and a proper fit. Measuring is also essential. The more accurate the measurements, the better turnout. 

For the flutes, or channels, I used the original fabric as templates. I took apart the original fluting, separating them into individual units. (I like to iron the old fabric. This flattening makes it easier when cutting the new fabric). 

Once the flattened templates are laid on the new fabric, it’s necessary to allow a few inches to the top and bottom lengths, so there is enough material to pull underneath the seat and over the chair's frame. The individual units are then sewn together. Once they are attached, they are sewn to the backing fabric on lines you have created by measuring the original fabric. The lines on the backing fabric must be narrower than the flutes to create enough space for the fiber fill or cotton. My channels measured 5-1/2”, so I drew lines that measured 4-1/2”. 

Prior to attaching the flutes, I made marks on the top rail of the chair to line up the fabric to keep it centered. The last fabric panel I attached was the back. After it stapled to the frame, I created the double cording, or piping. This is used to cover the staples and add a customized look to the chair. 

The fabric I used for this project was burgundy, with a diamond motif, that I had used last year to reupholster a bench. My customer saw this fabric on the blog and loved it, so she wanted it for her chair. Luckily I was able to get the same fabric! It’s one of my personal favorites. You can view that bench by clicking on this link: http://finalefurniture.blogspot.com/2021/11/antique-bench-trash-to-treasure.html

This chair was a true challenge, but with each project, I learn and advance my upholstery and sewing skills, which I truly enjoy.

View of repairs 

*As pictured on the left, you can see the areas where the chair was damaged and needed repair. This needed to be done prior to the leg refinishing and upholstery.

A Very Old Rocking Chair Revival

Rocking Chair After
Refinishing w New Leather

Old Broken Chair
Before Refinishing

When we get an item of furniture, it varies in degrees of just
how bad it is and how much work it requires to get it looking good again. Jim and I love a challenge. The uglier it is, the more we love restoring it, because it provides us an opportunity to make it beautiful once again, in most cases, better than new. 

This old rocking chair was exactly the type of piece that gets us both excited in anticipation of what’s inside, what we’ll find and how to best treat the piece with the care it needs. And this one needed a lot of love. The springs were literally popping through the deteriorated fabric (see photo below). The stuffing was long gone and the webbing was hanging from the underside of the seat.

The first step in this type of restoration is removing all the old materials. And this chair had a LOT of decorative (at one time) nail heads that needed to be removed. Nail heads usually get bent when they are installed because the wood is so hard, it bends the nails, so they can seldom be reused. I recommended instead of using nail heads, I’d replace them with new welting, which is also known as cording or piping. This is a cleaner, more updated look and still appropriate for this type of chair.

Motor Coach Bench Upholstery

Bench After
New Fabric

Bench Before
New Fabric

This summer I added sailboat cushions and patio furniture cushions to my collection of upholstery work. I also reupholstered a bench seat and back cushions for a motor coach as well as all new window valances for same motor coach. 

My customer had wanted an updated look for the early 2000’s motor coach and chose a lovely blue material with a denim style and feel. She loved blue, so blue was what she chose. The fabric was a dream to work with and durable enough to sustain a lot of wear. It will stand up to many glamping trips for years to come.

The original cushioned back was fluted, but she wanted one single cushion instead of separate fluted sections. The foam required for this cushions was six inch foam to adequately fill the space. This involved removing the cushions, backing and the top and front “L” shaped trim pieces. The rest of the motor coach also were given updated window treatments to match the seating, therefore many individual pieces required to be stripped of all old fabric, update the worn foam valance sections and replace with the new blue fabric. Everything had to be carefully planned out and marked to assure each piece would be reassembled into the same spot. This was an organized way to tackle this project. The more pieces, the better you have to keep track of which one goes where!

I installed a new zipper into each cushion, since the old zippers were metal and too small for these large cushions. I prefer the newer continuous zippers which can be cut to any size, making the fit of the cushions back into their new covers much easier. If it can taken apart, it can be put back together. This applies to pretty much anything with upholstery work.

Antique Solid Cedar Chest Refinished

Cedar Chest After

Cedar Chest Before

This is one of many cedar chests we have refinished, but it is the third one that was solid cedar; it had no veneer on the exterior. It was in pretty good condition with just a few minor scratches on the top left side in the back. Because it was solid cedar, those scratches were easily sanded away, bringing out the natural beauty and scent of the wood. 

My customer had used it as a coffee table with a glass top, so it will be protected and serve a dual purpose for many years. Cedar chests are one of my favorite furniture items because they are so versatile. In addition to storing linens, they make great toy boxes, a place to hide Christmas presents from snooping children and a great place to store seasonal clothing because of their natural moth repelling fragrant interiors. There’s nothing quite like the smell of a cedar chest. The cedar tree is one of many nature’s beautiful contributions to a family’s needs in the form of storage, seating and beauty. 

In addition to their versatile properties, cedar chests come in various shapes, sizes and styles. The waterfall cedar chest is very common with its curved front top and heavy lid. Many of these cedar chests were built in the 1940’s, used for linens and towels. Some cedar chests have legs with drawers, in addition to the lid-top storage interior. My personal cedar chest has a built-in shelf that is a perfect place to keep smaller items like my husband’s ties, socks and table runners. I love it for storing my quilts and extra sheets. If you don’t have a cedar chest, you may find one at an estate sale or at an antique store. If they need to be restored, you may get it for under $100.00. The best deal I got on my first cedar chest which was a 1945 waterfall style, was $5.00 at an estate sale. I doubt I’ll ever find one that cheap again!

You can see the other cedar chests we’ve refinished by clicking on these links:

https://finalefurniture.blogspot.com/2019/11/solid-cedar-chest.html
https://finalefurniture.blogspot.com/2016/08/1948-lane-cedar-chest_22.html
https://finalefurniture.blogspot.com/2015/04/elegant-cedar-chest-revival.html
https://finalefurniture.blogspot.com/2013/12/1945-lane-waterfall-cedar-chest.html
https://finalefurniture.blogspot.com/2012/06/my-waterfall-cedar-chest.html