Two Night Stands

Maple Night Stand Before

Walnut Night Stand After

This lovely maple table, one of the two I refinished, was in pretty good condition to start with, just needed to be stripped and stained with walnut to match the other furniture in the bedroom it was to be used in.

Spindles are always a lot of work and this one was no different. The spindles were time consuming to strip and I had to make sure all the old finish was entirely removed before I could sand it for the final time to properly prep it for staining.

Antique Mahogany Table Makeover

Mahogany Table Before

We've done plenty of tables since we started restoring furniture, but this by far was one of the most unique antique tables. This was a lovely "sewing table" with fluted edges on the top shelf and beading on the edge of the lower shelf. Unfortunately its structure was quite wobbly, because the points of

Mahogany Table After

attachment were very delicate and the legs were spindly and thin, which affected the overall stability. The only thing we could do to shore then up was add a few pin nails on the back side of the legs at the attachment point between the two shelves.

This table was in great overall condition, but the row of beading on the bottom shelf had beads missing, which needed to be replaced. I searched online for the right size replacement beads and discovered a few things. The first, beads such as the ones on this table are difficult to find, plus I was not able to get furniture beads in a dark

Antique Parlor Chair

Parlor Chair Before

Parlor Chair After

This little antique parlor chair was in excellent condition except for the seat, which was dented inward from being used. The stripping process took a great deal of time because the chairs by their nature have a lot of surface area that requires a lot of hard work to strip. When spindles are involved, it takes even longer.

Spindles are done by using a toothbrush dipped in stripper and then dipped in lacquer thinner and lots of brushing over and over to remove both stripper and lacquer thinner, which melts the stripper. This is quite a messy process that is time consuming as well as tedious.

Once all the goop was removed, I used steel wool dipped

Antique Dresser with Mirror

Antique Dresser Before

Antique Dresser After New Stain

Throughout the years we have done a good variety of dressers, each one different, with its own personality. Some of the dressers were tall, others were long and low with plenty of drawers. 

This antique dresser had three spacious drawers and a great looking mirror, with wood that was in excellent condition featuring a unique scroll design. The mirror itself had some age marks, but I always feel that this element adds to the character of the piece. 

The top of the dresser had

Old Rocker Makeover

Chair Before

Chair After

This rocker had a great structure, but the fabric was shot and needed to be replaced. It had also been used as a scratching post for a couple of cats, so the fabric on the backside was pretty torn up. My customer had asked for the chair to be refinished in addition to replacing the old, worn and torn fabric with fabric she had left over from a previous reupholstering job I had done for her dining room chairs. (See link below).
http://finalefurniture.blogspot.com/2018/06/french-dining-chairs-reupholstered.html

After removing the old fabric, as I had suspected, the chair had been stuffed with horsehair on the

Old Toy Chest Makeover

Toy Chest Before

Toy Chest After

Every so often I get a piece of furniture that is unique, completely different from other pieces I normally get such as tables and chairs. This piece was one of those interesting furniture items that I love because I can really feel my creative juices flowing at the prospect of making it look great.

An older gentleman and his wife who reside here in Marine City brought this to me to be restored. He told me it was used as a toy chest in Hamtramck and had bought it for his grandson. This man was a retired antiques dealer who has traveled across the country (in an RV), buying and selling antiques. He saw this unique piece and felt compelled to buy it for $75.00, but knew it needed more work so he brought it to me. I was thrilled!

Country French Table

Table Before Refinishing

Table After Refinishing

Tables are probably the most common refinishing jobs we acquire and most of the time we refinish and stain the entire table. Sometimes we paint tables. For this table, we combined both techniques, using stain and paint to create a harmonious new look, a perfect facelift.

This table had been stored in a barn for many years until someone had started working on the top, stripping off most of the paint. The base, however, still had a few layers of paint on it. For this table there were at least two, maybe three coats of paint, which required a great deal of time to remove. Wood carving tools were used to get into the "nooks and crannies" of the surface as it was quite porous, therefore it had absorbed all the original white paint. Since the top would be stained, it was necessary to remove every spec of paint. If you don't remove all the paint, it will still be visible when you apply stain, especially dark stain as in this table, which was stained dark walnut.

Since the original casters were well worn, we replaced them with new black rubber casters. The sides and base were painted antique white, which completed the "Country French" look the customer had wanted to achieve. This table had great bones and needed a bit of creative elbow grease to bring it back to life. Mission accomplished!

We had also done a dining room set using the same technique, combining paint and stain in the same way. Check out this blog post to see that: https://finalefurniture.blogspot.com/2017/02/from-amish-to-amazing.html

Bloodwood Chair

Chair Before Refinishing

Chair After Refinishing

Strong, sturdy and comfortable, this chair was somewhat of a surprise to my customer who thought it was an oak chair. After stripping, I discovered that it was not oak, but actually made from exotic bloodwood, found in Brazil and Australia. This wood is unique in that when the tree that it comes from is cut, you can see red “blood” dripping on the cut piece, hence the name. It is a hardwood with lots of color and movement. In addition to the run that runs through this wood, there are also yellow and gold shades, which complement the luscious red tones. It’s a gorgeous chair to be sure.
The stripping process revealed a lot of red in the wood, which had already been seeping through the old, worn surfaces, especially around the arms.

With the natural red tones of this chair, golden oak stain which was what my customer had originally requested, would not have worked. I opted for red mahogany, which not only brought out the chair's natural color, but worked well with the varied tones which gave the chair the exotic look that it deserved.

After using the red mahogany stain, I finished it with two coats of semi-gloss polyurethane so that this chair will last for many years to come.

Update as of May 12, 2019: I just finished the “sister” chair for this one, except it was a rocking chair. You can read about it here: http://finalefurniture.blogspot.com/2019/05/bloodwood-rocking-chair.html

Antique Spindle Table

Antique Spindle Table Before

Antique Spindle Table After

In restoration, spindles are simply not our favorite things to refinish for obvious reasons; they are a LOT of work. This table, however, required only a sand "touch up," for the legs. Only the top was stripped and sanded down to bare wood, then stained with golden pecan stain and finished off with three coats of semi-gloss polyurethane.

The legs were lightly sanded and touched up with walnut stain, since they were originally made from walnut, so keeping the stain original was the right choice. Likely this table dates back to the early twentieth century, or late nineteenth century judging by its design and the many spindles used to create it. You can usually spot an older piece of furniture by the screws, how it it assembled and the way the wood is connected.

There are other telltale signs, such as the natural patina of the wood, which as it ages, can become dull, the finish almost completely gone as was the case with this table. This is a plus because it makes the tedious job of sanding less time consuming than removing all that old finish which can take days. All in all this little table looked completely different once the top was refinished and the legs were refreshed with a bit of stain and new polyurethane.

This table had a lovely burled maple with a center point pattern. This designed is achieved by cutting the tree section in quarters, then matching the four sections so they meet in the center to create a unique and harmonious, gorgeous table top. Never doubt the value that refinishing an antique can bring to your old furniture. If you own it, you already have the value in the furniture. It's always worth saving a piece such as this.

Spindle Chairs, Oh My!

Spindle Captain Chair
Before Refinishing

Spindle Captain Chair
After Refinishing

I'll be brutally honest. I absolutely do not like to refinish anything with spindles. Simply because spindles require a great deal of time due to their shape and amount of detail. When it comes to chairs, that translates into many, many hours of tediously time-consuming work. There is just no way to do it quickly. Stripping just one chair can take up to a week and that's if if you work on it daily.

For this set of chairs (two captain, two regular), the entire refinishing process took several weeks, because there were so many spindles on the top and bottom of each chair.

Bar Stool Gets New Upholstery

Bar Stool Before

Bar Stool After

This bar stool was in desperate need of new fabric, otherwise it had great bones. The fabric was circa 1980 and had seen better days. Ripped on the seat it needed replacing.

The wood was teak as it was originally used on a boat. Still in great condition and sturdy, this heavy chair only needed new an updated look.

In order to reupholster the seat, I removed the arms and flipped the chair upside down to remove the staples which held the old, outdated and very stiff fabric in place. The foam was yellowed, but otherwise still usable. I decided to use the old fabric as a template, which needed to be taken apart so I could design a new seat with the existing fabric to get the right measurements, which is essential to get a good fit. It was much easier than I thought it would be and I was satisfied with the way the new fabric hugged the seat perfectly.

Two-Tier Antique Mahogany Table

Table Before Repair

Table After Repair & Refinishing

This table came to me as you see in the photo on the right, with three legs that were broken, the center piece which held them together was missing on two out of the three legs.

These missing sections had to be reconstructed using a template, traced from the legs themselves. This was an lovely antique two-tier table commonly seen during the 1920's and 1930s. Many people remember these tables in their grandparents homes, so they now hold a special place in our hearts along with all those memories. Commonly used for knick-knacks, plants, collectibles and many other

Tiny Rocking Chair

Rocking Chair Before

Chairs are the most commonly restored and refinished items that we receive. Chairs come in many styles, sizes, shapes and are made of too many types of wood to list, but they have one thing in common; they are not easy to refinish due to the many surfaces they tend to have. This tiny rocking chair once belonged to a little girl who has since grown up and wanted to preserve the many memories she likely had while enjoying the time she spent in this rocking chair.

Rocking Chair After

She may have sat by a window and enjoyed a Nancy Drew mystery novel as she rocked in time to the suspenseful mystery unfolding before her. Perhaps she stacked her stuffed animals on this chair to "keep it company" while she was at school. No matter how she used this little gem, likely she enjoyed it as a child and now as an adult, would like to see her own children make their own memories. This was a generational rocking chair meant to be passed down. As it where, the rocking chair had a couple of broken spindles in the center of the back. In fact, the entire chair came apart upon closer inspection, so repairing and gluing the broken spindles in place was the first thing that had to be done.

French Dining Chairs Reupholstered

Armchair Before

If you have ever wondered why reupholstering a chair is costly, this is why. It's a LOT of work! Today I finished working on six dining room chairs which included two French armchairs and four regular chairs with caning for the back. The French armchairs had a padded back which was open (so the fabric was actually on front and back) as well as the seat. I was uncertain exactly how the fabric was attached to the chair, as there were no nails or staples visible. The reason for that was that the staples were hidden in a 1/2" deep groove, which was created with a router so the welting could be pushed into it.

Antique Cedar Chest Revival

Cedar Chest After Refinishing

One of my favorite projects to refinish and restore is a beautiful cedar chest such as this lovely antique. The best part of this restoration was that it had retained all the original details such as the four vertical rows of rope braiding that embellished the front as well as the decorative trim surrounding the lid and another row of trim along the bottom. The chest was in pretty good shape overall, with surface scratches marring its top. Otherwise, it was in excellent condition.

Unlike other cedar chests I've done, this one had separate ball type feet which lifted it off the ground, allowing for easy relocating while working on it. Unfortunately, all that detail requires a great deal of time to remove the old finishes which requires a lot of time, patience and the right tools.

Cedar Chest Before Refinishing 

Never underestimate the power of an old toothbrush! Yes indeed a toothbrush is a key element to removing all that yucky, sticky residue that clings to the wood after you brush on the nasty stripper.

A good stripper will burn your skin on contact, so wearing gloves is essential while stripping. (I also keep a clean bucket of water on hand just in case I need to stick my hand into it. Ah, the burn!) A toothbrush, wood carving tools and a good brass brush are a great combination of tools to remove gooey varnish from all those nooks and crannies that would otherwise be impossible to reach. The ultimate goal is to reveal bare wood, that once sanded, is ready for staining. For this lovely cedar chest I used red mahogany stain and semi-gloss polyurethane, which brought out the natural beauty of the wood, showing its grain.

Cedar Chest After

Cedar Chest Before

It never ceases to amaze me just how awesome the wood looks once all the old finishes are removed and the lovely wood beneath is revealed. This was definitely one of my favorite cedar chests to work on because it had all those lovely details, which shows off its unique qualities and of course, the lovely craftsmanship that went into making it.

For other cedar chests I've refinished, you can click on these links:
http://finalefurniture.blogspot.com/2016/08/1948-lane-cedar-chest_22.html
http://finalefurniture.blogspot.com/2017/04/decorative-walnut-antique-cedar-chest.html
http://finalefurniture.blogspot.com/2017/05/solid-cedar-chest-with-copper-accents.html
http://finalefurniture.blogspot.com/2015/04/elegant-cedar-chest-revival.html
http://finalefurniture.blogspot.com/2013/12/1945-lane-waterfall-cedar-chest.html
http://finalefurniture.blogspot.com/2012/06/my-waterfall-cedar-chest.html
http://finalefurniture.blogspot.com/2014/10/solid-cedar-chest.html

Beautiful Antique Buffet Refinished

Buffet Before Refinishing

This was one of my favorite pieces to restore. It had been in the family for years belonging to a beloved grandmother who had passed on, so I really wanted to do it justice. Other than a few minor surface scratches on the top, the rest of this buffet was in amazing condition with everything still in tact. It was a fairly large piece, tricky to load in the truck.

Buffet After Refinishing

I love working on mahogany and cherry wood. The top of this
buffet was cherry while the rest of it was solid mahogany. The four front legs had detailed spindles which required a great deal of time and effort to strip thoroughly. I removed the back upper edge so the veneer that had been peeling away could be glued back in place before it was securely glued into the original holes.

Two front drawers and two cabinets, one on each side, gave this buffet a nice, balanced look. I chose to use dark walnut stain with satin polyurethane after everything was stripped and sanded to bare wood, always the first step of any refinishing project. The top received four coats of polyurethane for extra protection and durability.

Brand new hardware made all of our hard work "pop" and looked beautiful with the newly refinished surface. And boy, did it ever look great once it was all done.

Dresser Chalk Paint Makeover

Dresser Before Chalk Paint

Dresser After Chalk Paint

It's hard to believe that this lovely oak dresser was once used to store tools. It had been in a garage for many years being used as a tool bench and work surface so there was a bit of warping, but overall it was still in great shape. Although it had seen better times, the bones and structure were still good and we knew we could make it pretty again. We were both up for the challenge. (This was the last item in the "chalk paint makeover" using Annie Sloan's chalk paint.)

This dresser required some carpentry work before any painting could be done. The top had been split into two pieces, so Jim had to "biscuit" the two sections together and clamp them tight, then fill in the seams so that once painted, you would never know it had been broken. The left front leg had its back part broken off completely, so Jim re-engineered a new leg section, forming it perfect to match the right leg which was still in tact. Some of the drawers didn't open and close very well, so they required a bit of shaving on the table saw.

After he was done with his part of the job, I then sanded the sides and got busy painting. For this dresser, I mixed three parts graphite with one part French Linen which yielded a gorgeous color of a slate-ish gray, perfect for this particular piece of furniture. The thick, rich paint went on smoothly and looked terrific. I knew I would love this piece, since I just knew it would take on the largest transformation of the other pieces I had painted. Using clear wax on the entire dresser with black only on the bottom for accent was just enough to give it a sultry, rich look and a durable surface

The new brass drawer pulls provided the last touch of "bling," which was absolutely the crowning jewel for this amazing old girl. Wow!

Bench Gets White Chalk Paint

Bench Before Paint

A bench such as this one provides a great place to sit practically anywhere in your  home. But like with many pieces of furniture, after a while you tend to overlook this well-loved item. You may feel a bit guilty because you still love it, but know it needs that special something. In this case, the bench was destined to be a brand new look, which was accomplished by applying Annie Sloan's "Old White" chalk paint and finished with Annie Sloan's clear wax to seal it.

Bench After Paint

By its nature, this bench was a very labor intensive item to work on because of the amount of surface area, and of course, the spindles, which are difficult to paint. Spindles are my least favorite aspect of any furniture painting, restoration or refinishing job because they are, well, spindles. (Don't get me started!)

Chalk paint doesn't require a great deal of sanding or other prep work commonly needed to guarantee a greatly finished painted product, but I chose to lightly sand the entire bench anyway because that's just how I roll. Call it a pet peeve, but I feel that a little bit of sanding is better than no sanding.

I chose to brush the paint instead of spraying because I feel that you still get better coverage and a thicker, richer end product with brushing and for this piece of furniture, it worked quite well. That's another benefit of chalk paint; you don't see the brush strokes as it dries very smooth. The Old White paint was a light and bright color which literally changed the personality of this bench from outdated to outstanding. I added the customized stencil flower for a little something extra and it looked great. This bench received clear wax only so it will be protected from scratches and will be easy to care for.

Couch Table Chalk Painted

Couch Table Before Painting

This [behind the] couch table was the second project I painted using "Annie Sloan's" chalk paint and wax system. As in the Queen Anne Table in the blog post below, I used Annie Sloan's French Linen chalk paint.

I gave this table a shabby chic "distressing" by

Couch Table After Painting

scraping away the paint randomly with steel wool and a folded scrap of 100 grit sandpaper. After the paint had dried, I finished the table with generous coat of Annie Sloan's clear wax, then highlighted the border detail with Annie Sloan's black wax which brought out the border detail along the edge of the table top.

Once the wax had dried 24 hours later, I was able to lightly buff the table until it had a smooth finish which will be easy to maintain and provide a lovely, durable piece of furniture for many years.

Queen Anne Table Chalk Painted

Queen Anne Table Before

This was a lovely Queen Anne table in need of a new look and it was decided that paint would achieve this nicely.

Queen Anne Table After

Chalk paint is great to work with. The first coat shows the brush strokes, but this goes away after you paint the second coat giving you great coverage. It also dries very quickly, in 20 minutes so you can easily finish a project from start to finish the same day. Chalk paint has unique qualities and those qualities allow you to experiment with finishes, such as waxing. Prior to this project I had not heard of chalk paint waxing, but I was willing to give it a try.

Entertainment Center Downsized

Entertainment Center Before

As far as projects go, this was by far one of the largest in size as well as reconstruction. The original entertainment center consisted of the far left and far right panels only. After a while, the owner decided to have a center section built for the television and hired a carpenter to construct it so it would match the original bookshelf and desk areas. He did an amazing job in replicating the design of the original piece and it had served its purpose.

But this entertainment center had to go through yet another transformation. This one involved keeping the carpenter's addition of the television section and removing the far left panel altogether, reducing the piece to two sections, thus downsizing it considerably. It was necessary to cut the center and left sections and building a brand new left side panel which would support the center upper shelving units. This was no easy feat, but with a bit of creative re-engineering and reconstruction, a vision became a reality.

Entertainment Center After Reconstruction

The entertainment center was to be painted dark gray and fashioned with updated brushed nickel hardware, which completed the transition from outdated to updated on an otherwise functional piece of furniture.

If you have that special piece of furniture that you have grown fond of, be it something that has been in your family for generations or something you really love, for those pieces it's better to keep them (as you have invested in it already) instead of purchasing something new, which may not work as well as what you already own. This is a good example of what can be done with a perfectly good piece of furniture. Paint and new hardware creates an stunning, modern look which will function for many years to come. "Cheaper to keep her."

Teak Table and Chairs Upgrade

Teak Table and Chairs Before

Table and Chairs After

Every so often we get a special furniture job which requires lots
of attention. This very curvy teak table with matching corner chairs was such a project. I had never seen another table and chair set that looked like this one, with chairs that literally wrapped around the curved corners of the table.

Indeed this was a nice little package of table and chairs which was being upgraded from worn outdoor to being used as a kitchen table.

Chair Before

Chairs After Stripping Raw Wood

My customer wanted a whitewashed look to match her cabinets. I had not used this technique before, but was ready to give it a try. But first the tedious and time consuming process of stripping and sanding had to be done. And wow! It was deceivingly harder than we had thought it to be, because chairs by their nature have a LOT of surface area and these chairs, with their unique curvy feature had an angled corner leg, which created a lot of tiny crevices to get into and strip so that they would accept the new stain.

Chair After Staining

The table had a center support with four branches that supported it and didn't interfere with the way the chairs pull up to the table. After sanding the top to bare wood, the gorgeous teak that was hiding beneath layers of outdoor wear became visible. It made sense to turn the table upside-down and work on the underside that way. After two long days of carefully stripping and sanding the detailed underside, the table was ready for stain. Each chair took a couple of days to fully strip and sand so they would accept the stain well.

Teak Table Before

I used "Coastal Boards" stain, which was actually an off white shade that, unlike paint, wiped off easily and left a beachy style finish which was very similar to the whitewash technique. The finished set looked great, exactly what I had envisioned. The teak took the stain well and ended up with a slightly creamy appearance to give it an updated, modern look to be enjoyed for years to come.

Completed Set in Kitchen

Teak Table After