Antique Stained Glass Door Revival

 

Door Interior
Before

This antique door was well over 100 years old and had seen plenty of years of wear and weathering. The cracking was pretty severe and the windows, while amazingly weren’t broken, needed some TLC because the framework was deteriorating and held in by glaze. Unfortunately, upon removing some of the paint we discovered the door was not stainable, so our customer chose a fresh coat of paint.

The stripping process is always the most tedious in any refinishing project, but for doors a lot of the difficulty comes in with the type of paint that was used. The older the door, the harder it is to remove the paint. Milk paint was frequently used back then and with our experience, is quite difficult to remove. We either use a chemical stripper or a heat gun (or both) when we remove the old paint from most projects. 

Sometimes it’s just not possible to remove all the paint so we remove as much as we can then sand it smooth and prep it for paint. A coat of primer is necessary for any paint project whether it has had paint on it previously or not. Especially raw wood projects which always require primer. Once primed, painting flows smoothly. 

Door Interior
After

This door required more work because the customer needed the door knob and hardware moved to the opposite side because of where the door would be located, so it was necessary to remove the old hardware, fill the holes left with wood pieces, dowels and filler, sand it smooth and drill new holes on the other side of the door so that it opens correctly. The new hardware they chose was brass.

This door required refinishing as well as carpentry work. Jim made new moldings for the stained glass panels and replaced the center clear glass. The door was out of square so he made sure all was square and plumb which is necessary for a smooth installation.

As you can see in the photo to the right, once installed, the stained glass looked fabulous, adding charm and character to the kitchen. The color of the glass was not visible from the exterior due to the angle of the photo. Photos below are of the exterior before and after photos.

Door Exterior
Before

Door Exterior
After

Dresser Chalk Paint Makeover

Dresser Before Chalk Paint

Dresser After Chalk Paint

It's hard to believe that this lovely oak dresser was once used to store tools. It had been in a garage for many years being used as a tool bench and work surface so there was a bit of warping, but overall it was still in great shape. Although it had seen better times, the bones and structure were still good and we knew we could make it pretty again. We were both up for the challenge. (This was the last item in the "chalk paint makeover" using Annie Sloan's chalk paint.)

This dresser required some carpentry work before any painting could be done. The top had been split into two pieces, so Jim had to "biscuit" the two sections together and clamp them tight, then fill in the seams so that once painted, you would never know it had been broken. The left front leg had its back part broken off completely, so Jim re-engineered a new leg section, forming it perfect to match the right leg which was still in tact. Some of the drawers didn't open and close very well, so they required a bit of shaving on the table saw.

After he was done with his part of the job, I then sanded the sides and got busy painting. For this dresser, I mixed three parts graphite with one part French Linen which yielded a gorgeous color of a slate-ish gray, perfect for this particular piece of furniture. The thick, rich paint went on smoothly and looked terrific. I knew I would love this piece, since I just knew it would take on the largest transformation of the other pieces I had painted. Using clear wax on the entire dresser with black only on the bottom for accent was just enough to give it a sultry, rich look and a durable surface

The new brass drawer pulls provided the last touch of "bling," which was absolutely the crowning jewel for this amazing old girl. Wow!

Antique Vanity Makeover

Vanity Before

Vanity After

This vanity had been in my customer's  in-law's family for a few generations. Neglect and time took its toll on this lovely vanity as the scratched surface attested to. However, I assured my customer I would make it shine and indeed, I did. The first step was to remove the hardware then get it ready for sanding and stripping, which was immensely tedious because the sides have a fluted rounded edge which required a metal brush to remove all the previous finishes, all part of the stripping process. 

Birch Wine Bar

Bar Before

Bar After

This simple bar was quite the challenge! Made of solid birch, this bar was in my customer's family since the mid-1960s. We received it in the condition it had been for over 50 years, painted white, with more than its share of scratches. Old hardware dated this piece, so we had our work cut out for us. 

You never truly know how much work a piece is going to be until you get into the "bones" of it. Stripping this small bar was deceptively difficult for a few reasons; there was a lot of surface area and the raised panel details as well as the legs and inside was an enormous task. The interior glass holders each took close to two hours to strip. When you strip painted surfaces and plan on staining them, it's necessary to remove every speck of paint. If you don't, the stain will not be able to soak into the wood as those tiny paint specks remain and stick out like the proverbial sore thumb. 

Antique Oak China Cabinet

China Cabinet Before

China Cabinet After

We acquired this gorgeous oak China cabinet and immediately saw its potential. It was in almost perfect condition, with three mirrors, two glass shelves and two wood shelves. It had the original hardware and needed just a little work to expose its original glory.

Of course, as with all projects, I get "before" photos before beginning any project. Luckily, this large cabinet had wheels, which made it much easier to maneuver.

Other than minor scratches, the cabinet needed little other than touch-up and a good cleaning. I carefully removed the shelves, then unscrewed the angled shelving brackets, each made of brass, as well as the original brass handle and put them aside to be polished. The bowed glass door's molding had a few missing nails, so I used my pin nailer to reinforce the tiny 1/4" molding, holding the glass firmly in place. (I love my small nailer!) This process can be a bit dicy, because the molding holds the glass in place, therefore you don't have a lot of space in which to shoot nails, as the last thing you want to do it break that glass! Once that was done, I cleaned the interior glass first, then the exterior, which showed a lot of dust and smudges, likely from being stored.

1960's Bedroom Set

Night Stand Before

Night Stand After

This was a large furniture job for a client in Grosse Pointe. This bedroom set included a nightstand (pictured left and right), a tall dresser, a low dresser, a mirror (not pictured) and a headboard. This was a popular 1960's, Early American style set. I actually had a nightstand very similar to this one as a child. It was popular back then.

My client wanted to keep the same finish and use the same handles. I started with the low dresser, then the tall dresser, nightstand and headboard and finished with the mirror. I spent two or three days removing the tarnish from the handles, then polishing them until they looked new once again. I love the shiny new brass finish revealed after all that detail work.

There are always surprises when you remove the factory finish from furniture and this set was no exception. The wood was pine, but because various sections of board were used, there was a great deal of color variation. Personally, I love this look as you can really see the wood grain, which tends to be hidden with a factory treatment. This is the beauty of hand-finished products; seeing the gorgeous wood beneath.

Low Dresser Before

Low Dresser After

Headboard Before

Headboard After

Tall Dresser Before

Tall Dresser After

Umbrella Stand Shines Again

Umbrella Stand Before

This is an unusual piece of furniture to be sure. We did work for a man who had bought two items of furniture from us and had already had us refinish a table for him. He had picked this up and wanted to see if we could do something to improve its looks. What is it? Well,

Umbrella Stand After

it's a very unusual Umbrella Stand, made out of about three different types of wood; maple, pine and mahogany. The front is a curved brass sheet which was badly marred and tarnished. The photo on the left shows the one spot Jim rubbed out the brass, revealing what promised to be a shiny metal buried underneath years of oxidation.