Antique Stained Glass Door Revival

 

Door Interior
Before

This antique door was well over 100 years old and had seen plenty of years of wear and weathering. The cracking was pretty severe and the windows, while amazingly weren’t broken, needed some TLC because the framework was deteriorating and held in by glaze. Unfortunately, upon removing some of the paint we discovered the door was not stainable, so our customer chose a fresh coat of paint.

The stripping process is always the most tedious in any refinishing project, but for doors a lot of the difficulty comes in with the type of paint that was used. The older the door, the harder it is to remove the paint. Milk paint was frequently used back then and with our experience, is quite difficult to remove. We either use a chemical stripper or a heat gun (or both) when we remove the old paint from most projects. 

Sometimes it’s just not possible to remove all the paint so we remove as much as we can then sand it smooth and prep it for paint. A coat of primer is necessary for any paint project whether it has had paint on it previously or not. Especially raw wood projects which always require primer. Once primed, painting flows smoothly. 

Door Interior
After

This door required more work because the customer needed the door knob and hardware moved to the opposite side because of where the door would be located, so it was necessary to remove the old hardware, fill the holes left with wood pieces, dowels and filler, sand it smooth and drill new holes on the other side of the door so that it opens correctly. The new hardware they chose was brass.

This door required refinishing as well as carpentry work. Jim made new moldings for the stained glass panels and replaced the center clear glass. The door was out of square so he made sure all was square and plumb which is necessary for a smooth installation.

As you can see in the photo to the right, once installed, the stained glass looked fabulous, adding charm and character to the kitchen. The color of the glass was not visible from the exterior due to the angle of the photo. Photos below are of the exterior before and after photos.

Door Exterior
Before

Door Exterior
After

Antique Bench Refinished w/needlepoint

Bench After

 

Bench Before

Although sturdy and strong enough to seat an adult, this antique bench was in dire need of refinishing. The front veneer had peeled off entirely while other areas that had veneer were loose. 

Since this was a natural hardwood, I removed the veneer completely since it looked better without it. The rest of the bench had no veneer and the wood was in great condition, but a bit scratched, mostly on the feet. The legs were a Queen Anne style, commonly used for this style of bench.

Prior to refinishing the bench, I first removed and found it had the original straw and batting, which was commonly used for making cushions one hundred years ago. I replaced that old straw with a 2” foam cushion and a layer of quilt batting for extra seating comfort. 

The bench required stripping, sanding and staining. I chose a mid-tone chestnut stain, which brought out the natural beauty of the wood. Satin polyurethane finished off the freshly stained wood so it remains protected for many years to come. My customer had her own needlepoint seat cover that she had wanted to use to replace the stained, worn old topper. The transformation was incredible, a nice piece of furniture anyone would be proud to own.

Peg Leg Knitting Table Refinished and Repaired

Knitting Table Before

An antique knitting table such as this was useful for storing knitting needles and yard as well as other essentials a knitter would use in her arsenal of creative tools. Somewhere along the line the front left leg broke, thus had a “peg leg” appearance and didn’t stand up on it’s own. Luckily, we were able to repair the broken leg by drilling a hole on the top portion and the broken part of the leg, then glue them back together with a dowel. This is the correct and most durable way to repair a leg such as this one, which isn’t very large to start with.

Knitting Table After

The rest of the cabinet needed some touch up, a knob replacement on the bottom drawer and a completed refinished top that was stripped, sanded, stained and protected with two coats of polyurethane. The entire bottom of the sides was missing, so we replaced that with matching plywood cut to size. It simply won’t do to have your knitting needles fall out and end up on the floor. 

This was the second knitting cabinet we’ve done, but this one was a bit lighter wood than the first one which you can see by clicking on this link: http://finalefurniture.blogspot.com/search?q=knitting+cabinet

It’s nice to have a few projects that we can compare to other projects we’ve done that are similar. These knitting cabinets were commonly used at the turn of the century and have been preserved throughout the years as they can are versatile and can be used as a display cabinet in a hallway or a great storage spot which doesn’t take up a lot of space.

Oak Chairs Refinished

Oak Chair After

Oak Chair Before

We restore more chairs than anything else and the reason is simple. Everyone has them and eventually, they get pretty worn, damaged and no longer look good so they will require an overhaul. 

Depending on the amount of damage a chair retains, refinishing can be “lightweight,” meaning a little clean up and perhaps touch-up staining to a total restoration which requires the chair to be stripped down to bare wood (the preferred method), sanded thoroughly, wiped clean and stained with the choice of the customer.

This is one of two identical chairs that needed complete restoration. This one had some water damage on the top, but was overall in pretty good condition. Still strong and not requiring gluing of loose joints, once the stripped and sanding was complete, we applied a fresh coat of English Chestnut stain and two coats of semi-gloss polyurethane. Not only did the refinishing repair the damage, it brought out the luster and beauty of the wood which had been hiding under years of water damage and grime. Never underestimate the power of refinishing a chair! 

You’d be surprised how many people dumpster dive and bring us chairs that someone else had tossed and we made pretty again. The old saying “One man’s trash is another man’s (or woman’s) treasure,” is really true. It’s a shame to thing someone had tossed furniture away only to have it completely turned into a usable treasure, so keep that in mind when you look at an old item of furniture and think, “Is it worth it?” I can tell you with absolute certainty that it is always worth it if the furniture item has good bones. Furniture made of solid wood is built to last a lifetime. And not just the lifetime of a person, but several lifetimes throughout generations if it is taken care of. Maintaining the integrity and classic look of an old piece of furniture, be it a chair, table, dresser or cedar chest is keeping a part of history that we can learn from for generations to come.

Antique Eastlake Cabinet Upgrade

Cabinet Before

Cabinet After

Once used as a tall dresser, this antique cabinet was in pretty rough condition prior to restoration. Actually, upon receiving it and getting started on the refinishing process, it sort of, well, fell apart. The piece had seen plenty of use over its sixty-plus years and many of the joints had come unglued, so it made sense to simple separate those loose joints and disassemble it to properly strip, sand and stain it the right way. 

The interior of this cabinet had three adjustable shelves, which had a unique adjustability system. The wood in the rear and front of the cabinet had slots which held small sections of wood that each shelf rested on and were easily removed so that they were easily adjustable to whatever height you needed. 

The bottom drawer was an unremarkable feature of the cabinet, the lovely brass drawer pulls blended into the background. It was also in need of a new bottom since the original one had been damaged and was no longer usable. Once the new bottom was built and installed, it was once again strong and usable. 

The hardware was polished, which included the drawer pulls and hinges. The bottom drawer, once almost invisible, was a focal point, the brass pulls looked like new. The keyhole slots were original, but two out the three were broken and had to be replaced with newly constructed, custom made key slots which looked almost identical to the original. When a piece of an old item of furniture is missing, it’s almost impossible to find that exact piece so a bit of ingenuity and design comes in handy to create a replica. 

The right side of the cabinet did not have glass, but plexiglass that was held closed with a piece of cardboard. Of course this wouldn’t do, so we replaced the plexiglass with glass and added a magnet at the top of the right (opening) door so that it would stay closed. A new stain and three coats of polyurethane to protect the surfaces and this old beauty got a major upgrade. Amazing how beautiful wood that hides beneath years of usage becomes when it is revealed with refinishing. This was indeed a lovely piece of furniture that we enjoyed working on.

Oak Teacher’s Desk Revival

Teacher's Desk Before

Remember elementary school? Do you still remember your teacher’s desk? Well, this was once a teacher’s desk that used way back in the day of notebooks (not laptop computers), pencils, typewriters and maybe even an apple on the teacher’s desk. 

Unlike the desks I remember from my early school years, this one had a unique feature; a slide-out, built-in filing cabinet with many cubby holes and slots for letters and other teacher-ish items. I had never seen a desk like this one. And you can imagine how extremely heavy it was!

Teacher's Desk After

The desk top had been destroyed by fire. Our customer thought the top had water damage, but upon closer inspection, it was fire, not water that had destroyed the top. We also noted that the original desk was likely a roll top, which was no longer part of the desk. Unfortunately the top’s damage was so severe, it was not able to be restored. It had to be replaced. 

We generally prefer to use the original pieces of our furniture restoration process, but when that isn’t an option, we rebuild it to resemble as closely to the original design as possible. The burnt top was comprised of border sections surrounding the center sections instead of larger boards simply glued together to create a uniform, single directional top. This was more involved and complex than a directional top and required much more wood in various lengths, but the new top was outstanding when it was done. Jim did a tremendous job in rebuilding the  top to best represent the original one. If I was the teacher, I’d give him an A+!

Tedious would be an understatement in describing the process of refinishing and restoring this desk. Every drawer had to be removed and labeled. The pull-out filing cabinet was its own entity that required even more disassembly and extra steps. The unique part of this little cabinet was that it rotated so that the teacher could easily access the files in the back. It also had its original snap-in alphabetical folders that the teacher probably used to keep track of her students. The handles did not come off, so the stripping and sanding process involved keeping them in place and working around them. The inside of the desk,  as well as the back, also had to be stripped, sanded and refinished. The stain used was golden oak with satin polyurethane to protect the desk for years to come. 

Burnt Top

Newly Built Top

Antique Windsor Chair Refinished

 

Windsor Chair
Before

This is what is called the “Windsor” Chair. It has the classical round form with spindles on the top and bottom of the chair, with the center split and mounted on a curved flat platform that turns into the top of the armrest. These chairs come in plain or rocking chair styles. 

This chair was over 100 years old and original in its antique styling and manufacturing. It had a center split that had been repaired before we got it, however, the stripping on this type of chair is very intense and takes a long time. (We hate spindles!) Not only did it have spindles, it had two spindle bases, one in the center and one on the bottom seat, therefore making the stripping much more time-consuming. 

Windsor Chair After

One of the most difficult part of refinishing this type of chair is that no power tools can be using when sanding, therefore, everything is hand sanded which adds to the time spent removing the entire old finishing. Some chairs are easier to work on than others. This one was not an easy redo because of the spindles, upper and lower. The chair was made of sturdy walnut, so that’s the end choice color we used to stain it. 

Finished and protected with satin polyurethane, it actually turned out beautiful, despite the splotchy look on the bare wood, which is characteristic of old furniture once stripped. If you ever wondered why chairs cost so much to strip, try your hand at one of these and you’ll understand. It’s a very tedious process and takes many, many hours and lots of patience and of course, the right tools to do the job. The most important tool is patience and tenacity. 

Antique Rocking Chair New Caned Seat

Here's another old beauty of a rocking chair that need the broken caned seat replaced. Like many older chairs with caned seats, they tend to get broken after years of use because the cane gets brittle and if a child happens to put their knee onto it, well, there goes the caning with a hole in the middle. If the caning is slightly bent in the middle, it can be made taut again by placing a damp towel on the seat overnight. This technique softens the cane, thus tightening gradually when it dries and giving it more use, at least for a little while. But when it completely breaks through, the only alternative is removing the old,

Antique Rocking
Chair After

broken cane and replacing it with new cane. This is a “strand” cane chair, which means that it has holes surrounding the chairs seat where the cane strands get woven through. This is a seven-step process that is quite tedious, but if you listen to music or a podcast (like I do), it’s not so bad. It’s actually pretty relaxing once you get into the groove of it and allow your fingers to work their magic. 

For this chair, I used 2.25mm fine caning. This is based on the size caning that was in the chair originally. There are methods to measure the distance between the center to center holes to determine the proper size caning to use, but I prefer just to measure the existing old cane to make sure it will fit since the hole technique isn’t always accurate. The reason is that when many of these very old chair were made, whoever drilled the holes didn’t always measure the exact distance between holes as well as the size of the holes, therefore to use just the holes is not the more accurate way to get the proper new caning installed. 

In my experience, it’s better to use a slightly narrower size than one that is too large as this will be a real problem during the final binding step. If the cane is too big and overfills the holes, it’s nearly impossible to get the final strands through the holes without pushing the cane back out of the holes you’ve worked so hard to get securely in place.

This was to date my very best caning job because everything flowed smoothly and the caning was even and straight. The trickiest part was the the curved arm was attached very closely to the holes on that part of the seat, so the arms had to be lifted up enough so that I could thread the caning through the 6 or 7 holes that were very close to the bottom of the armrest. Some of those holes were drilled at an angle, so that made caning in those areas even more challenging as I tried to find the angle of the hole. However, once that was completed, the rest was easy by comparison. Caning is always done with the first step going front to back, underneath, then pulled through the hole and brought forward again. You repeat this process from the center all the way to the right (or left) side then finish off the other remaining side in the same manner. The next step is horizontal, left to right, starting in the back upper corner of the chair, following the same weaving. 

Third step is going over the first step, keeping the strands to the right of the first vertical strands. This is so that when you weave the fourth step, you go over step 3 and under step 1. This is the actual “weaving” part of caning which will set up the diagonal weaves that go from the upper right to the lower left corners. Finally, you weave from the upper left to the lower right corners, going under vertical and over horizontal one way then the opposite for the other side. 

Binding is what finishes off the top. A slightly wider section of caning is measured around the circumference of the chair. This covers up the holes with sections of caning coming up and going down the same hole, pulling tightly to keep the top edge secure. After this is done, you tap in a 1/2” finishing piece to plug the hole(s) where the caning started. It sounds a lot more complicated then it is, but if you follow the steps, you too can become a caning master. It’s definitely a great skill to have, some call a “dying” art as not many people are doing this anymore. It’s also a unique and creative way to add texture to your home with caned pieces such as speaker covers, cabinets and footstools in addition to chair seats and backs.

Here’s the video of the final step of me caning this rocking chair:

https://draft.blogger.com/blog/post/edit/5936537173467203420/6863734281706129925

Maple Table Makeover

Refinished Table

Nothing says family more than a large dining room table. And, because we love our tables, we use them a lot! Therefore, they take a lot of abuse and as a result, get worn, scratched and marred with the passage of time. This is a very large maple dining table with a leaf that showed signs of wear on the surface. 

Luckily there weren’t any super deep gouges, so it was doable to strip, sand and stain the table and bring back its glory. Choosing a newer, darker stain, mocha, brought out the natural woodgrain and tones of the table which seemed hidden by the wear previous to refinishing. Finished off with three protective coats of satin polyurethane, this worn out table was once again a shining star, ready for many family meals.

Table Before Refinishing

Antique Dresser with Mirror

 

Dresser Before

Dressers are important pieces of furniture with the important purpose of keeping your sweaters and other items handy and at your fingertips. Nobody said a dresser needs to be boring, so why not take a look at that old dresser in your grandmother’s attic and examined it with a critical eye and imagine it refinished. 

Dresser After

This dresser had been a family heirloom that had seen some wear. The mirror was original and had some marking on the back side, but was still serviceable. A fun aspect of obtaining and refinishing antiques is finding something that dates an item. This dresser had old newspapers on the back that dated back to November of 1913. Made of solid oak, this dresser was a lovely piece of furniture worthy of restoration.

As with most mirrored pieces, they are refinished separately, which requires a great deal of care. Especially with a mirror (because who wants seven years of bad luck?) The lovely curves of the side bars of the mirror really added character to the overall look of the dresser. It was indeed a special element that makes these antiques so special and individually unique. Two top drawers with a single larger drawer and a front curve mimics the curve of the mirror frame as well as the top, which had the most damage. After stripping, sanding and staining, we protected this dresser with two coats of polyurethane. 

Luckily, we are usually able to remove most surface scratches on furniture, so this piece had a great finish. The exception to that rule is when an item has veneer with deep scratches. You can only sand veneer so far before you remove it completely and end up with what appears to be a large patch where the plywood shows through. That’s why we love working with solid wood. It’s much more durable and sturdy and refinishes well, with a better final result. Anything made of particle board isn’t even worth refinishing because it’s not “real” wood. You can’t beat solid wood for furniture, that’s why antiques are always worth refinishing so they can be kept for another few centuries. 

Children’s Checkers Table Set

Checkers Table Before

Checkers is a favorite pastime of many people, young and old. I remember growing up with checkers and getting really angry when my brother would beat be. He called me a “sore looser.” Well, who wants to lose? I didn’t. This little table had a well-worn checkerboard center made of very thin plastic which had seen better days. The plastic was peeling up and was simply not fixable. 

Checkers Table After

We made a few suggestions to our customer on how to refresh this table with a “new,” yet original look that could have been created originally and would last for many years to come. 

We decided to create a new checkerboard center by using wood instead of plastic or glass mosaic (another cool choice). This required two types of wood, walnut and maple, cut into even widths and the length of the center section, then cut the glued sections to rotate them180 degrees which created the perfect checkerboard. It worked swimmingly well and looked fabulous. Once the checkerboard center was done, the table was stripped and refinished along with the little seats. The finished checkerboard table with the perfect stain was indeed a work of art upon completion. Kudos to my husband, Jim, who can make miracles happen with wood.

Table Set Before

Table Set After

Checkerboard Antique Card Table

 

Card Table Before

Card Table After

Every once in a while we get a totally unique piece of furniture that is one in a million. One of the many aspects of furniture restoration is the wide variety of items that come our way. It’s always a surprise! At times the surprise comes when we see it. Other times the surprise comes after we remove the years and years of grime to reveal the beauty beneath it. This antique card table with a checkerboard center was such a piece.

It’s hard to know origins of furniture, such as how old an item is, where it was made, what kind of wood is was made from. We have seen mostly oak, walnut, cherry and even some more exotic woods such as bloodwood and olive wood. At times we’ve seen wood we can’t easily identify. With this unique table we quickly realized it was made of many types of wood combined to create a work of art which ended with a center design in a checkerboard or chess table.

However, it was completely covered with years of grime, dirt and who knows what else. Hidden away in a garage for over thirty years, this table was likely overlooked and became part of the back storage of the space it occupied until my customer yanked it out with the intention of getting it refinished. It looked like a major undertaking since there were many pieces of wood missing that would have to be replaced as well as all that grim removed with stripper and carefully sanded so that none of the wood would be destroyed in the process. And yes, each piece of wood you see has been individually placed into the table! This alone makes it a highly unique work of art. 

Once stripped, the gorgeous wood beneath was exposed. It was comprised of maple, bird’s eye maple, walnut and mahogany. Since many of the original tiny pieces were missing, it was necessary to cut and carefully place each missing piece in its place so that it blended in with the table and look as if they were always there. As you can imagine, this was a very time-consuming process. After all those missing pieces were installed and glued, it was then stained and protected with four coats of strong polyurethane so it will hold up for another one hundred years at least. A timeless beauty can say, “Checkmate.”

Card Table Before

Card Table After

Oak Dresser Hidden by Green Paint

 

Dresser After Stripping

Dresser Before Stripping

This little dresser is similar to a few others we’ve done that had the same overall look and design. However, this one was painted green. In our experience, sometimes when a piece of furniture is painted, there’s a good reason for it. Upon stripping this little dresser, we discovered that one of the drawers had a “patch,” which meant that someone had added a different type of wood that didn’t match the original oak that was used when it was built.

Luckily we were able to apply the stain so that it covered the entire piece in a way that looked as it would have looked originally. Likely, it had never been stained, just painted after it was built. It was old though.

When painting furniture, it usually doesn’t matter if wood styles are mixed because the paint covers it all evenly. But when a person wants something stripped and stained, refinished per se, if the wood is patched with non-original wood, this results in a variance of stain colors since different types of wood accept stain differently. 

A good example would be if you apply a dark stain to a light wood such as pine, it would certainly darken the original raw wood but wouldn’t be as dark as if you used the same stain on walnut, which is a darker wood to begin with. It’s always easier to go darker upon refinishing/restoring but much harder to go lighter. Not to say that it isn’t possible to do this as it all depends on the type of wood that was stained originally. Sometimes you simply don’t know what the raw wood will look like until it is stripped as years and years tend to oxidize the wood, making it darker than the original stain. Most of the time the wood, when stripped and completely sanded, is much lighter than the old finish. This allows for plenty of stain choices as it is fun to experiment with how the various stains draw out the wood’s original beauty. This is one of the most rewarding aspects of refinishing...seeing the final results when applying the stain. Ah, it’s pretty once again!

Antique Mahogany Swivel Table

 

Swivel Table Before

Another beautiful swivel table! This antique was made of mahogany with brass accents. The lower portion of this table had a unique “harp” design with three brass prongs, that cleaned up real nice. The top was in rough shape and had seen years of use, including water damage likely from placing a planter directly not the wood. It’s always a good idea to have a planter with a tray or aluminum pie tin to eliminate water damage. 

Swivel Table After

This table was in need of stripping, sanding and new stain. We chose special walnut stain and three coats of semi-gloss polyurethane to ensure protection from everyday use. All the brass accents, feet, harp metal and two small knobs (not seen in photo) were cleaned and polished. Polishing the brass, truly accentuates the refinishing process. It also adds a special “bling” to any piece of furniture, much like the right jewelry does for an outfit.

This style of table is used for playing board games or cards, as it has a “secret” swivel compartment beneath the top that is accessible by rotating the table 90 degrees, then opening one side to reveal the compact area beneath, just large enough to hold note pads, decks of cards and paper goods. When not being used as a game table, it folds in half and can be pushed right up against a wall and used for decorative accents such as plants, lamps or collectibles. Now that it has been refinished, this table will likely be used for many card games and other fun activities.

Antique 19th Century Caned Chairs

Antique Chair After

 

Antique Chair Before

Here we go with more chairs! This time it was a set of four (4) chairs, all in need of TLC. These chairs dated back to the late 1800’s, so they were 19th century chairs that had seen a lot of use, therefore a lot of wear and tear, literally. 

Originally the chairs had caned seats, but over time they likely broke and someone decided to cover the seat with stamped leather, or rather, a leather-look-alike that seemed more like a heavy paper between layers of very thin leather. Broken and no longer able to seat a person, it was high time to remove the leather “fix” and replace it with the original woven caning. But first, the chairs all needed to be stripped, which for this type of chair is very time-consuming because (you guessed it), spindles. Yup, spindles are what takes a long time to strip because there are many of them and they are rounded, making them inaccessible from one angle, therefore it’s necessary to rotate the chair continuously while stripping. 

A chemical stripper was the best option for these (compared to a heat gun), because it melts away the old, worn finish and reveals the wood beneath. Once all the old finish is removed, the chairs are then cleaned up by using soft rags (usually old t-shirts, which are excellent for this) and wiping away the residue left by the stripper with lacquer thinner or acetone. This is a necessary step prior to sanding or your sandpaper will clog up with the residue, making it difficult to remove. 

Starting with 100 grit sandpaper, the chair is prepared to accept the next grit, 150, until the final sanding, which is done with 220 grit. Once all surfaces are sanded, the chair is wiped with lacquer thinner on a clean cloth, allowed to dry, then it is ready for stain. This entire process (for this type of chair) can take from several hours to a few days. Again, spindles are a lot of work, therefore more tedious and time-consuming than flat surface chairs. Once the stain is applied with either a soft cloth or a brush, or both, you wipe away the excess stain, then enjoy the amazing transformation from raw wood to beautifully restored, refinished wood. 

We used "special walnut" on these chairs. The new stain brought out all that gorgeous woodgrain, which had been hidden by years of oxidation that happens over time. Once the chairs had dried from staining (we allow 24-48 hours), the first coat of polyurethane was applied. For these chairs we used a water-based semi-gloss, durable and easy to clean up after. That first coat protects the stain and prepares the wood for the remaining two coats that finish the chair. It is necessary to lightly sand between each coat of poly with a high grit sandpaper to give it “tooth,” which makes just rough enough to accept the next layer of polyurethane. Once the third coat was applied, the chairs were done and ready for the last and final step, install the new caning. 

These chairs had “press-in” caning, cane that comes in pre-woven sheets and cut to size, then installed and kept in place with spline. It’s necessary to soak the cane and spline for at least an hour (or longer) so that it is pliable enough to work with, otherwise it cracks and breaks. Caning “wedges" are used to “press” the edge of the cane into the pre-cut 1/4” groove in the chair. The chairs had a closely woven cane originally, so we chose the same style to keep it original.

It’s necessary to choose the right size of spline, which is based on the width of the opening, so that it keeps the cane in place while completely filling the groove. If the cane is too loose, it will not keep the cane taut. It’s a tricky process because once you have pressed all the cane into the groove, you glue it slowly, allowing the glue to run into the groove, starting in the back of the chair. Once it is glued, you push the spline into place, tapping it with a hammer as you go. If the spline has been adequately soaked, it will bend easily around curves. If not, it can break, especially if those curves are tight. 

Luckily these chairs’ curves were fairly wide, so it wasn’t too difficult to bend them around the edge. Once you reach the back where you started, make a small pencil mark and cut the spline to match the starting point at an angle and tap it with a hammer in place. After all the spline is installed around the entire seat, hammer the spline so that it is level with the top of the chair. There will be caning strands popping out that were left over from the placement after the spline is installed, so they must be trimmed off. I use a sharp chisel and snap them away by tapping on a hammer close to the spline, which removes the excess. You can also use snippers. This completes the caning process. Allow the cane to dry at least 24-48 hours before you sit on the chair.

Table Re-painted in Beautiful Black

Table Before

We mostly prefer stripping furniture to reveal the beautiful wood beneath and then stain it as it would have been done naturally, but it doesn’t always work out that way and there’s a good reason why the furniture was painted instead of being stained. This antique folding table was a prime example of why painting is better than stain as it would not accept stain. The reason was that it was made up of different types of wood and most of the paint had penetrated the wood’s surface, therefore making it not stain-worthy. Luckily our customer understood the situation and opted for paint instead.

Table After

We stripped this table as we do most other furniture items with stripper and plenty of elbow grease. Once the table was completely stripped, each area then gets carefully sanded to remove as much rough surface as possible. This prepares the piece for the next step, primer. Any time you have raw wood, primer is a must do as raw wood will soak up all the paint if it is not primed first. You can purchase paint with primer in it, but we prefer these processes to be kept separate because we find it gives us better results and a smoother finished surface. 

You generally don’t need polyurethane on a painted item unless it will be used outdoors, but then you would be better off using outdoor paint. Adding polyurethane or lacquer to a painted item will over time turn it yellow. Just a little piece of advice to keep in mind...

While we can paint furniture in any color the customer chooses, as this is a personal preference, but black seems to be the most popular colors because it is neutral and versatile and looks great when accompanied with brass accents such as this table’s feet. We always clean the hardware and additional accents such as brass feet on tables or hinges, because it finishes the piece nicely, giving it “bling,” as well as a fresher look. 

This table had two fold-out leaves, which doubled its size, making it a great table to use when you need more seating. Its compact size made it easy to store when not being used for a dining table and can instead be used as an accessory table. The classic black was a great choice and kept the original integrity of the table in addition to giving it a fresh, new appearance that will look great for decades.

Newly Caned Dining Chair

 

Cane Chair Before

    My caning abilities are really being tested these days, but the

Cane Chair After

more caning I do, the easier it becomes and the more enjoyable. I’ve rounded another curve in my progress and have become more than just sufficient, in fact, I'm pretty darn good at it. This exquisite dining chair was likely the last survivor of a six to eight set of predecessors, therefore it deserved special treatment and caning done right. 

    This chair had been caned many years prior and had been broken, likely by a knee or a child that used it as a way to sneak cookies out of grandma’s cupboard. Cane gets brittle after so many years, therefore it is vulnerable to breakage as it ages. My choice to keep the cane original (not stain it) is to add years of service to the chair by allowing it to age naturally.

    This chair was “strand caned,” meaning the cane comes in 6’-8’ lengths, then carefully woven, one strand at a time through pre-drilled holes surrounding the chair’s seat. It’s a labor intensive process, both in removing the old cane as well as weaving the new cane. Cane comes in various widths from very fine 2mm to medium 3mm or larger sizes 4mm and up. It’s important to determine the size of the cane in relationship to the holes, or it becomes very difficult the further you get into the process if the cane is too large since you will be pulling many strands through the same holes over and over due to the nature of the weaving. While the caning process is repetitious, each chair is unique in the way it is woven to accommodate the shape of that particular chair. 

    This chair had a curved seat, wider in the front than in the back, therefore it was necessary to double up the strands in some holes and omit others for that direction. The most difficult part of the chair was near the arms, because the cane moves around them beneath the chair so getting the cane to slide through those holes was tricky. Having the right tools is essential as they make the difference between a mediocre job and an excellent one. Strand caning is done is six parts; front to back, left to right, front to back again, diagonal one direction then diagonal in the opposite direction and finally, binding. When you first begin weaving, you use caning pegs (see photo below) to keep the cane in place. Eventually the cane becomes tight so they are no longer needed. 

    The very last step is the tie off the cut cane beneath the chair by tucking it up under the loops created by the weave then tie them tightly prior to snipping off their ends. It was really a nice looking chair one the new cane was in place.

Caning pegs hold cane in place
during weaving process

Antique Oak High Chair

    

High Chair Before

    The very nature of a chair’s construction makes it quite time consuming

High Chair After

to work on. When a chair has spindles with curves and detail, the time spent stripping is even more time consuming than a relatively simple style. But the very best part of restoring any chair is the finished product, which always amazes me because of the drastic difference between how it comes to us and how it looks when it is restored. Yup, chairs are a lot of work, but the outcome is always worthwhile and successful.     

    A high chair such as this one was once used for a great-grandfather whom would have been seated in while his mother fed him mashed carrots. Needless to say if this chair could speak, oh what stories it would tell! Unfortunately, the most obvious story was that it was in need of restoration and repair. The seat was held together by panty hose (which works well in a pinch!)

    The center portion of the seat had split directly in the center as well as a minor split closer to the side. Therefore in addition to refinishing, it needed to be repaired first. The best way to achieve this and do it properly, was to take it apart, partially. Once it was separated all the way, it was cleaned and re-glued, then clamped overnight so that the glue would do its job and mend the splits. If this is done properly, the glue will hold for many years to come (providing a high school student that had long since outgrown the chair didn’t intend to sit on it!)

    After the chair was strong and secure again, the slow and tedious process of stripping and sanding was next. There are no shortcuts when it comes to stripping a chair, any chair. It simply takes a long time because chairs have a LOT of surface area. This chair had such pretty grain that had been hiding under many years of use. When this is stripped and sanded away, that original grain shines through, giving the chair a new life by revealing its original beauty. We selected “gunstock” stain and a satin finish for this high chair. I absolutely love the way the chair turned out! Once again structurally sound and the gorgeous wood revealed, this chair is ready for another century of being a family heirloom.

Check out the other high chair we’ve done by clicking on this link: https://finalefurniture.blogspot.com/2020/06/height-chair-before-height-chair-after.html

Oak Table for Church Services

Oak Table Before

This was a beautiful oak table hiding beneath years of usage. Used in a local church, this table’s place was at the front of the church used in their Sunday services as a communion table. It had been covered with a white tablecloth that hid the lovely carving (which you cannot see in the “before” photo. The top of the table had lots of wear and some water damage, but luckily it was superficial and mostly on the surface, not beneath the wood’s fibers. Therefore a good stripping and sanding process removed the unsightly stains and damage to reveal the original gorgeous oak hidden by years of normal wear. 

Table After

The table’s bottom cross piece, which was connected only with dowels, had come apart and was spinning wildly during transport. This was the first order of business, to repair that loose cross piece to stabilize the table and keep it from shifting again. To achieve this, we drilled two holes on each end of the underside of the board with a pocket screw assembly, then screwed it tightly after applying a generous amount of wood glue to the end cap. 

After clamping the sides together, the center board was again secure and super strong and won’t come apart anytime soon. (We always make any repairs prior to the refinishing process). Once the center board was dried and secured, we stripped and sanded the entire table, revealing the lovely carving which read, “This do in remembrance of me.” 

We chose “gunstock” as a stain color, which is a gorgeous golden rust with red tones. It’s my new favorite stain color as of this year and we’ve used it many times as it works for any type of wood. Followed up with four coats of satin polyurethane on the top and three coats on the rest of the table, this lovely oak piece will glorify the church and its services for many years to come.

New Front Door

Door Before

Door After

A front door is most important feature of your home. It keeps out weather, makes a home secure, invites people inside and is a representation of the people living in the home. Therefore, a front door should be well maintained, weatherproof and attractive as well as functional. This front door had been exposed to the elements and over time it became weathered and worn. (We took the photo on our work table so we don’t have a “before” of the door in the home, but our customer sent us the “after picture.

The interior was in great shape, but the exterior needed the most attention. However, upon closer inspection, the interior had been affected by the exterior’s wear because the door had warped, therefore the trim surrounding each panel was lifting enough so that one could get a decent scratch at the least and broken or missing pieces which would be not easy to replace. Before we could start on the exterior, we needed to address the interior’s warping issue by carefully removing the “lifted” trim and sanding each piece down just enough so they could “curve" with the warped panel and would lie flat again. Then we could refinish the weathered front. This door was solid oak and weighed a ton. The door knocker was brass along, with the handle/lock, which carried a hefty price tag (quality costs money!) This door was begging to be made handsome once again. 

Because of the amount of trim and the narrow passages between the trim. stripping was intensely tedious and took a lot longer than expected (it always does!) Stripping took several days and sanding a few more. Since this was our customer’s front door (he literally didn’t have a front door for a week, other than the storm door), we needed to move as quickly as time would allow. We used a variety of hand tools in addition to the much-used orbital sander. Our favorite hand tools are a set of wood carving tools that allow us to get into the nooks and crannies and corners, so we can remove the residue that is left by stripping the old stain and varnish. Once that’s done, lots and lots of sanding prior to the fun part, staining. For this door we used golden oak stain which matched the existing interior color perfectly. To protect the exterior, we applied three coats of satin polyurethane. Once the finely crafted brass hardware was reinstalled, the door was complete, looking brand new again.